Current builds of the Mackanized programs. Each needs a licence key file
(engineflasher.key or tcmflasher.key) in the
same folder as the exe; the Logger accepts either and comes free with
every licence. Each program has a short how-to page. A Tactrix OpenPort
2.0 works without any driver install: ours is built into every program.
Licence key
Trionic 7, Trionic 8 and Bosch ME9.6: full read and write,
free. Create your own engineflasher.key in a minute. Other
ECUs and the TCM Flasher are paid and issued by us.
TCM Flasher
AF40-6 / AW55 transmission control modules.
Version 1.6.7-beta built 2026-11-21, 12.7 MB
Saab 9-5 2002-2010 (AW55): a 6 ms write pace can be chosen in Settings, between 8 ms and 4 ms (about 12 minutes). The 6 ms pace has not been run on a bench or a car; the standard pace is unchanged and is still the only one proven on cars.
Download TCMFlasher_v1.6.7-beta.exe How to use it
SHA-256 4f67c77dc46db4df26c1f6018aaee97dacf8ec60d49c1267a9751a08d134eb99
Builds older than 1.2.14 can read but are refused a write; update before flashing.
Earlier versions
- 1.6.6-beta 2026-11-20 LAWICEL CANUSB: the interface is used through its D2XX driver only; its COM port is no longer offered (reads over the COM port stopped with a timeout), and the interface is listed once. If the interface cannot be opened right after it was closed, the program waits and tries again for up to 2.5 seconds before it reports the error.
- 1.6.5-beta 2026-11-19 Fix: on a car with a Trionic 8 engine control unit the VIN could not be read with a LAWICEL CANUSB (or with any interface after it had slowed down), so a read or write stopped at "No module on this bus returned a VIN". Saab 9-5 2002-2010 (AW55): the write pace and its time are shown in the log, in Swedish too, and a write at Standard pace uses much less processor. Settings: an error while saving is now shown.
- 1.6.4-beta 2026-11-15 Saab 9-5 2002-2010 (AW55): writing is back at the pace proven on cars (about 24 minutes). The faster pace in 1.6.2 and 1.6.3-beta could stop a write after the erase (timeout waiting for 0x76). If that happened to you: update, keep the power connected and run the write again with the same file. A faster pace can be chosen under Settings (Advanced) for testing; Standard is the default.
- 1.6.3-beta 2026-11-13 The interface now passes only the gearbox control unit's answers once the unit is known (raw-CAN J2534, Kvaser, CANUSB, CombiAdapter), so the rest of the car's bus no longer fills the interface's buffer; on some interfaces (Scanmatik) that lost answers and slowed or stopped a job. The scan for the car's VIN still listens to every module. An interface that cannot filter works as before.
- 1.6.2 2026-11-10 Saab 9-5 2002-2010 AW55 (IVLAN): the write now takes about 7 minutes instead of up to 25 on Windows, the row pace is kept on a real clock and set to 2 ms (bench verified byte-exact). Flash tune on a bench unit without a VIN works for licences allowed to work bench units: read the unit first, then flash.
- 1.6.0 2026-11-06 Out of beta. The user agreement is updated (private licence holders, use outside the EU/EEA including the USA and Canada at your own risk) and is shown once more for you to accept. Saab 9-5 2002-2010 (AW55) is no longer beta: reading and writing are proven on customer cars, and the write no longer asks for the beta disclaimer.
- 1.5.15-beta 2026-11-06 Sign in with your e-mail address when no .key file is found; OBDLink EX and LAWICEL CANUSB out of beta; OBDLink old firmware connects (writes refused); AW55 file checked against the unit's application number
- 1.5.14-beta 2026-11-03 1.5.14-beta: new Erase fault codes (button 6) for NG cars - ECM, TCM, ABS/ESP, EHPS, CIM, FPCM and XWD, codes saved first, airbag and I-bus never touched, TCM adaptations untouched; clear finish dialog after every job (Programming complete / what to do next / Reset adaptations / Erase fault codes / Show procedure); OBDLink erase fixes.
- 1.5.13-beta 2026-10-27 Sessions now report how long reading and writing took on your adapter (bus time only; no names, no VIN) for the new adapter speed table on the download page.
Engine Flasher
Trionic 8, Trionic 7, ME9.6, ME(D)9.6.1, E39, EDC16 engine ECUs.
Version 1.4.19-beta built 2026-11-16, 15.3 MB
New: the engine ECU of the Opel Astra J OPC (E39A) can now be read. Writing an E39A is not supported yet and is refused before anything is sent to the ECU. The E39 and the E39A now use Mackanized's own build of the programming loader; the session log shows it as 'MPC5566-LOADER: MACKANIZED.EU'. An E39 is read and written as before, with the same licence. If an E39A restarts when the loader is started, the program now says so and nothing is read or written.
Download EngineFlasher_v1.4.19-beta.exe How to use it
SHA-256 1e166d3146633aa4bc9a399c247daefde4174ecd23564c2541008bd85f0d9514
Builds older than 1.3.1 can read but are refused a write; update before flashing.
Earlier versions
- 1.4.18-beta 2026-11-13 The interface now passes only the answers of the ECU being worked on, for every engine family and every interface that can filter (J2534, Kvaser, CANUSB, CombiAdapter), so the rest of the car's bus no longer fills the interface's buffer; on some interfaces (Scanmatik) that lost answers and stopped a read or write before it began. The session log shows 'Adapter receive filter' with what was set; an interface that cannot filter works as before. Trionic 8: the questions asked before anything is erased are asked again when an answer is lost, and a bench ECU that has just been powered is waited for.
- 1.4.17-beta 2026-11-06 The user agreement is updated (private licence holders, use outside the EU/EEA including the USA and Canada at your own risk) and is shown once more for you to accept.
- 1.4.16-beta 2026-11-06 Sign in with your e-mail address when no .key file is found; OBDLink EX and LAWICEL CANUSB out of beta; OBDLink old firmware connects (writes refused)
- 1.4.15-beta 2026-11-03 1.4.15-beta: Delco E39 on Scanmatik SM3/SM2 uses one mixed-format channel (hardware ISO-TP; writes about 2x faster, no lost frames), smaller reads after a lost frame, loader exit confirmed before 'done'; every E39 read is now confirmed by the ECU's own MD5 per partition (boot and shadow row included) - a mismatch is re-read, and never saved as a backup; console runs reach the speed board; correct byte counts for region reads.
- 1.4.14-beta 2026-10-30 A full flash may change the software: a Trionic 8 write of a file with another software part number no longer stops to ask (the change is logged). E39: writing OS + calibration from a file built on another OS is refused, as E39 units only run their own OS. Pressing Cancel on a warning is now recorded as declined, not as a failed flash.
- 1.4.13-beta 2026-10-29 When the server refuses a job (for example a file stored under a region this unit never writes), the app now shows the server's answer instead of 'Could not reach the server'.
- 1.4.12-beta 2026-10-27 Sessions now report how long reading and writing took on your adapter (bus time only; no names, no VIN) for the new adapter speed table on the download page.
- 1.4.11-beta 2026-10-27 New: OBDLink EX (STN) listed as a BETA interface for ME9.6, MED9.6.1, EDC16C39 and EDC17 - identify and read; Trionic 7/8 and E39 are not available on it yet; writing over it is enabled per licence.
- 1.4.10-beta 2026-10-26 Fix: with a Kvaser interface selected as CANlib (not J2534), the program could stop responding on a car because of other traffic on the bus.
Mackanized ECU Logger
Live logging of the ECU's own values (ME(D)9.6.1, ME9.6, E39, EDC16) and of every module on the car's bus, Trionic 7 included. Free with every Mackanized licence.
Version 0.7.14-beta built 2026-11-21, 13.3 MB
New: markers. The Marker button or F8 puts a numbered marker in the log at once; Ctrl+K puts one and then asks for a comment, which is written to the session log under the same number. The log file gets a last column named Marker, empty except on a marked row. In Review the markers are orange lines on the timeline; M goes to the next one, Shift+M to the previous. New: own presets. My presets saves the channel list together with the layout of the dials and the strips under a name; it is listed with a star in the preset box and is on again the next time the program starts.
Download MackanizedLogger_v0.7.14-beta.exe How to use it
SHA-256 3e0e9f4f0baebb88506a88226c56d6c3cfbfb8576240db22579cbff0e60a3e38
Earlier versions
- 0.7.13-beta 2026-11-20 Trionic 8 (Saab 9-3 petrol 2003-2011 and others) can now be logged with an OBDLink EX. Limits on the OBDLink: the car's bus values and the raw CAN file are not recorded in the same session, only softwares the logger already knows (or an opened bin), and Trionic 7 still needs a J2534 adapter or a Kvaser. First release of this route: tested against a simulated adapter, not yet on a car.
- 0.7.12-beta 2026-11-20 Saab 9-5 diesel: when another device in the car (for example an eSID) asks the engine control unit at the same time, the logger asks again about 30 ms after the other device's answer instead of waiting 0.2 s, no longer answers the other device's reply, and says so once in the session log. LAWICEL CANUSB: an adapter that shows up both as a COM port and as D2XX is listed once.
- 0.7.11-beta 2026-11-19 Saab 9-5 diesel: the gearbox output speed is now shown in km/h, and the gear codes are explained (5-9 = 1st-5th, 12/13 = 4th/5th with lock-up). All cars: when the memory map cannot be fetched because the computer is offline, a box says so, points at Open A2L and says that only bus values and PID channels are logged without a map.
- 0.7.10-beta 2026-11-18 Saab 9-3 diesel (Bosch EDC16C39, 1.9 TiD / TTiD): values this control unit never gives out are no longer offered in the channel list, and a read is no longer placed across a memory area the control unit refuses. Before, the channels beside such an area were lost with it, and a log with only those channels stopped with "the ECU refuses every RAM read". Checked on a bench control unit (Z19DT / Z19DTH software) with the engine off. Three more diesel softwares are recognised (55572716, 55572721, 55579434).
- 0.7.9-beta 2026-11-18 Saab 9-5 diesel (1.9 TiD): the gearbox and the rest of the car are now logged from the car's bus beside the engine values (turbine and output speed, gear, torque limit, gearbox oil temperature, wheel speeds). These bus values are not yet checked on a 9-5 diesel and are marked so. A read the control unit leaves unanswered is asked again sooner, so the gap in the log is about 0.3 s instead of 1 s.
- 0.7.8-beta 2026-11-17 Saab 9-5 diesel (1.9 TiD): about 20 % more rows per second; values this control unit does not give out are no longer offered in the channel list, and one refused while logging no longer slows the whole log; a late value can no longer end up in the next channel's column; the log stops with a clear message if every read is refused. All diesels: an OBDLink no longer stops with an internal error when the control unit does not answer.
- 0.7.7-beta 2026-11-16 Saab 9-5 diesel (1.9 TiD, Bosch EDC16C39): the logger now finds the memory-read format this control unit accepts and reads in smaller blocks. 0.7.6-beta connected and was then refused on every read, so nothing was logged. The 9-3 diesel is unchanged. The status line no longer says "unknown software" when the map came from the server.
- 0.7.6-beta 2026-11-13 Trionic 8 on a bench: an ECU that has just been powered (for example through the Scanmatik relay) is no longer turned away as 'does not identify as a Trionic 8' while it is still starting; the question is asked again for a few seconds. Kvaser (CANlib) can now filter in the adapter as well.
- 0.7.5 2026-11-12 J2534 adapters (Scanmatik and others): the adapter passes only the ECU's answers from the moment the session opens, and the Trionic 8 name table is unpacked without leaving the adapter unread, so start-up no longer fills the adapter's receive buffer with the whole car bus. XWD cars: the ESP's request frame to the rear drive module is logged again.
Mackanized Flasher Experimental
The Engine Flasher and the TCM Flasher in one program: engine control units and automatic gearboxes of a Saab from one window, with your existing licence.
Experimental: this program is new and has had little testing on cars. The Engine Flasher and the TCM Flasher above remain the supported programs; use this one only if you want to try it, and report what you see.
Version 0.1.1-beta built 2026-11-21, 16.8 MB
First experimental build: the jobs of the Engine Flasher and the TCM Flasher for a Saab in one window, with your existing licence. New program with little testing on cars; the Engine Flasher and the TCM Flasher remain the supported programs. Please report what you see.
Download MackanizedFlasher_v0.1.1-beta.exe
SHA-256 53ec504c78f711b92702c71bca3dfe564b3f2ea8b5b0e46a59479077769a17e2
Speed by adapter
How fast each adapter reads and writes, from real customer sessions, measured by the flasher. Anonymous: only the adapter model is counted, and a row needs at least 3 runs. Fastest median first within each block; bus-time and older session-time figures, and bench power versus not recorded, are never ranked against each other. "Bus time" is measured on the bus; older "session time" also includes dialogs and waiting for you. Trionic 8 and E39 writes are not listed: those flashers skip blocks that already match, so the time depends on the tune. Speed depends on the ECU and the car as much as the adapter.
Engine flasher
Bosch ME(D)9.6.1, calibration: read
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 1:32 | 1:28 | - | 3 |
Bosch ME(D)9.6.1, calibration: write
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 0:35 | 0:34 | - | 3 |
Bosch ME9.6, engine calibration: read
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 0:50 | 0:50 | 2 | 4 |
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Chipsoft J2534 Pro fastest | 0:58 | 0:52 | - | 4 |
Bosch ME9.6, full: read
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 17:23 | 17:23 | 2 | 3 |
Bosch ME9.6, internal_mcp: read
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 3:34 | 3:34 | 2 | 3 |
Bosch ME9.6, main: read
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 13:49 | 13:49 | 2 | 3 |
Delco E39, calibration: read
Bus time, bench power
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 1:17 | 1:17 | 5 | 4 |
Trionic 8, application: read
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 1:36 | 1:20 | - | 4 |
Trionic 8, clone: read
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 1:28 | 1:17 | 12 | 5 |
Trionic 8, full: read
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 1:10 | 1:04 | 15 | 4 |
| CANUSB | 1:35 | 1:34 | 11 | 5 |
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 1:27 | 1:15 | 14 | 5 |
TCM flasher
9-5 AW55 (2002-2010), tune: write
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM3 fastest | 8:47 | 8:40 | 1 | 3 |
| Kvaser J2534 | 23:37 | 13:44 | 0 | 3 |
AF40 Gen2: read
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM3 fastest | 6:39 | 6:15 | 3 | 4 |
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Kvaser J2534 fastest | 7:14 | 6:43 | - | 4 |
| Scanmatik SM2 | 7:30 | 6:43 | - | 6 |
AF40 Gen2: write
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Kvaser J2534 fastest | 1:20 | 1:17 | - | 4 |
| Scanmatik SM2 | 3:08 | 3:00 | - | 7 |
AF40/AW55 Gen1: read
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM3 fastest | 2:57 | 2:55 | 3 | 8 |
| CANUSB | 3:11 | 3:10 | 3 | 3 |
| Kvaser J2534 | 3:23 | 3:22 | 2 | 3 |
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 3:00 | 2:53 | - | 17 |
AF40/AW55 Gen1, tune: write
Bus time, bench not recorded
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 0:51 | 0:50 | 9 | 3 |
| Scanmatik SM3 | 0:54 | 0:49 | 8 | 6 |
| Kvaser J2534 | 1:15 | 1:10 | 6 | 3 |
| Chipsoft J2534 Pro | 1:21 | 1:16 | 6 | 4 |
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 2:58 | 2:09 | - | 3 |
AF40/AW55 Gen1: write
Older sessions (time includes prompts)
| Adapter | Median | Best | KB/s | Runs |
|---|---|---|---|---|
| Scanmatik SM2 fastest | 1:54 | 1:51 | - | 6 |
The program checks this same list when it starts and tells you when a newer version exists. Windows may warn about an unknown publisher on a first run; the SHA-256 above lets you confirm the file is the one published here.